Broadcast Tools SS 2.1/Terminal III Manual de usuario Pagina 159
- Pagina / 188
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Appendix F: Redundant Backup F-1
Moseley SL9003Q 602-12016 Revision G
Appendix F: Redundant Backup with TP64
and TPT-2 Transfer Panels
F.1 Introduction
The Starlink SL9003Q and Digital Composite operate in a redundant hot or cold standby
configuration STL link using the TP64 Transfer Panel for transmitter switching. The Starlink
digital STL link may also be used in a redundant cold standby configuration with an existing
analog STL as a main or backup link when using a TPT-2 Transfer Panel.
F.2 TP64 System Features
• Redundant standby system accessory for Starlink 9000 QAM STL product lines.
• Manual transfer and Master/Slave selection by front panel push button.
• Front panel tri-color LED indicators display status of transmitter and receiver functions of
both Main and Standby radios.
• RF transfer relay provides high isolation, low insertion loss, and wide bandwidth, while
maintaining RF termination of the Standby radio transmitter.
F.3 TP64 System Specifications
Redundant Standby
System Frequency Range
0.5-2 GHz (limited by power divider)
TX Relay
Frequency Range
0 to 18 GHz
TX Relay Insertion Loss
0.2 dB max. (0-4 GHz)
TX Relay Isolation
80 dB min. (0-4 GHz)
TX Relay VSWR
1.2:1 max. (0-4 GHz)
TX Relay Switching Type
Make before Break, Transfer Switch (standby TX switched into
50 ohm power termination)
TX Relay Switching Time
15 mSec max
TX Relay Life
1 × 106 cycles
TX Relay & RX Power
Divider RF Connector Type
50 ohms type N (female)
RX Power Divider
Insertion Loss
3.2 dB typ. f= 1GHz
Control I/O Interface
Radio A & Radio B
DB-9 male (see Appendix)
- Starlink SL9003Q 1
- WARRANTY 2
- Table of Contents 7
- List of Figures 9
- 1 System Features and 11
- Specifications 11
- 1.1 System Introduction 12
- 1.2 System Features 13
- 1.3 Specifications 14
- 1.4 Regulatory Notices 21
- FCC Part 15 Notice 21
- 2 Quick Start 23
- 2.1 Unpacking 24
- 2.2 Notices 24
- WARNING 25
- 2.3 Rack Mount 26
- SL9003Q 2 or 4 Channel 27
- Receiver 27
- Transmitter 27
- RX ANTENNA 28
- Digital Composite 29
- SL9003Q TX Main Menu 30
- Scroll Right/Left to choose: 31
- AUTO/OFF/ON 31
- 2.6.1. Audio 32
- 2.6.2. Composite 33
- 2.6.3. Data Channels 33
- 2.7 Performance 34
- Receiver Performance Check 36
- 3 Installation 37
- 3.1 Rear Panel Connections 38
- CAUTION 39
- 3.2 Preliminary Bench Tests 41
- SL9003Q 2 Channel 42
- 3.2.1. RF Bench Test 44
- 3.3 Site Installation 50
- 3.3.1. Facility Requirements 52
- 3.3.2. Power Requirements 52
- (Typical) 53
- 3.4.3. Environmental Seals 54
- 3.6 Link Alignment 55
- 4 Operation 57
- 4.2.1 LCD Display 59
- Changes Made 64
- SAVE SETTINGS? 64
- 7.4 Screen Menu Summaries 65
- 4.4.1 Meter 66
- 4.4.2 System: Card View 66
- 4.4.4 System: Info 67
- 4.4.6 Factory Calibration 69
- Caution 69
- Section 4: Operation 4-15 71
- Section 4: Operation 4-17 73
- 4.4.9 System: Transfer 74
- 4.4.8 System: Date/Time 74
- Section 4: Operation 4-19 75
- 4.4.11 Alarms/Faults 76
- Section 4: Operation 4-25 81
- 4.4.13 Radio TX Status 83
- 4.4.14 Radio RX Status 85
- 4.4.15 Radio TX Control 86
- 4.4.16 Radio RX Control 86
- Section 4: Operation 4-31 87
- Radio TX Config 88
- MHz950. 0000 88
- Radio RX Config 89
- 5 Module Configuration 91
- AUDIO ENC 92
- CAUTION: 93
- S21 – Data Channel 95
- S23 – System Config 96
- 5.2.1. AES/EBU and SPDIF 97
- 5.2.3. Data Channel Rate 98
- 5.2.4. Board ID 99
- 5.2.5. System Configuration 99
- 5.3.1. Data Channel 99
- 5.7 Power Amplifier 105
- 5.8 MUX Module 106
- 5.9.1. External I/O 108
- Received Signal Level (dBm) 115
- Vout (Vdc) 115
- 6 Customer Service 117
- 6.1 Introduction 118
- 6.2 Technical Consultation 118
- 6.3 Factory Service 119
- 6.4 Field Repair 120
- 7 System Description 123
- 7.5 Introduction 124
- 7.6 Transmitter 124
- 7.6.1. Audio Encoder 126
- 7.6.5. Power Amplifier 129
- 7.7 Receiver 130
- 7.7.1. Receiver Module 131
- 7.7.4. Audio Decoder 133
- 8 Appendices 135
- A.1. Introduction 137
- A.2. Path Analysis 141
- A.2.2 Losses 142
- B.1.1 Why dBm? 151
- B.1.2 Audio Meters 151
- B.1.3 Voltage-Based Systems 151
- B.1.4 Old Habits Die Hard 152
- Conversion (50 ohms) 155
- Modem Splitter 162
- Audio Processor 163
- (Optimod or Equiv.) 163
- Data Sharing Device 163
- Radio A - MAIN Default 164
- Radio B - STANDBY Default 164
- SL9003Q Receiver 164
- FCC ID: CSU9WKPCL6010 171
- MOSELEY ASSOCIATES, INC 171
- ASSEMBLED IN USA 171
- Remote Control 172
- Broadcast Tools 172
- SS 2.1 BNC III 172
- Switcher/Router 172
- INPUT: 90-260V, 47-63Hz 177
- F.7 Software Settings 181
- F.7.2 TP64 Settings 181
- For Hostile Environments 183
- INFORMATION - FCC Form 601 187
Relacionado con productos y manuales para Redes Broadcast Tools SS 2.1/Terminal III
Redes Broadcast Tools SS 4.1 III Manual de usuario
(140 paginas)
(140 paginas)
Redes Broadcast Tools SS 4.1 III Especificaciones
(11 paginas)
(11 paginas)
Redes Broadcast Tools SS 4.1 III Especificaciones
(17 paginas)
(17 paginas)
Redes Broadcast Tools SS 4.1 III Especificaciones
(13 paginas)
(13 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales